Attributes

Productgroup ID	2
Repetition accuracy	± 0,015
Permissible vertical process force	100N
Lift of WT over conveyor medium [h0]	1,05
Dry room	<1
ESD	yes
Pneumatic straight connection [Ø]	4mm
required compressed air connection [pmax]	6bar
required compressed air connection [pmin]	4bar
Weight	0kg
Scope of delivery	Positioning unit,Sensor for position sensing of the clamping cylinder.,Fastening material,Pneumatic screw fitting (throttle non-return valve for intake throttling),Three SH 1/U switch brackets,Stop bushing
Delivery information	Fully assembled
Required accessories	Stop Gate VE 1,Damped stop gate VE 1/D
Preferred values	80,120,160

• Can be used with workpiece pallets WT 1/S, WT 1/K and WT 1/P
• Positioning via dowel pin and floating supported shaft on the side of the workpiece pallet
• Permissible vertical process force up to 100 N incl. workpiece pallet
• Repeat accuracy in X- and Y-direction: ± 0.015 mm
• One stop gate VE 1 or VE 1/D each must be used for pre-positioning the arriving workpiece pallet and pre-separation.
• The PE 1/P can be mounted directly under the conveying section or on the table top on an automated station without interrupting the section profile.
• The PE 1/P also enables the workpiece pallet to be accessed from below.

Positioning unit PE 1/P for WT 1/P
Repeat accuracy in X and Y direction: ± 0.015 mm, Can be used with workpiece pallets WT 1/S, WT 1/K and WT 1/P, Positioning via dowel pin and floating supported shaft on the side of the workpiece pallet, Permissible vertical process force up to 100 N inc

• 3D CAD
• Data Sheet

Stop Gate VE 1

Stop Gate VE 1

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Tilting stop gate; can be opened without causing abrasion on the workpiece pallet stop surface. Permissible total load of all workpiece pallets in the accumulation: 80 kg (with conveying speed 9 m/min)

Assembly instructions

CAD data

Stop Gate, damped VE 1/D

Stop Gate, damped VE 1/D

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Pneumatic damping can be adapted to the workpiece pallet weight Workpiece pallet minimum weight: 0.5 kg Permissible total load of all workpiece pallets in the accumulation: 12 kg (with conveying speed 6 m/min)

Assembly instructions

CAD data

Scope of delivery

Positioning unit PE 1/P for WT 1/S WT 1/K	Positioning unit	Sensor for position sensing of the clamping cylinder.	Fastening material	Pneumatic screw fitting (throttle non-return valve for intake throttling)	Three SH 1/U switch brackets
Positioning unit PE 1/P for WT 1/P

Positioning Unit PE 1/P

The workpiece must be fixed for processing in the processing station. The precision positioning units of the TS 1 make it possible to position the workpiece fastened on the workpiece pallet in a highly precise way in the processing station.

 

Positioning of a workpiece pallet in a processing station or on a manual workplace with very high positioning accuracy requirements

Example of switch bracket installation

1)	Not included in the scope of delivery

No.			3842998101	3842998102
ESD			yes	yes
Cleanroom class			ISO class 7	ISO class 7
Dry room	r.F.	%	<1	<1
Required compressed air connection	p	bar	4 ... 6 bar	4 ... 6 bar
Pneumatic push-in fitting	Ø	mm	4	4
Height to conveying level	h	mm	0,9	1,05

		Positioning unit PE 1/P for WT 1/S WT 1/K	Positioning unit PE 1/P for WT 1/P
	(mm)	± 0,015	± 0,015
F	(N)	100 N	100 N
p	(bar)	4 ... 6 bar	4 ... 6 bar
Ø	(mm)	4 mm	4 mm

Minimum WT changing times t

b (mm)	v (m/min)	t (s)
80	12	0,7
80	18	0,65
120	12	0,9
120	18	0,8
160	12	1,1
160	18	0,95