RETURN 120+ AL
| Productgroup ID | 2 |
| Effective sliding rail length | 0,742m |
| Actual chain length | 2x 0,2m |
| Weight | 1.95kg |
| Scope of delivery | Incl. fastening material |
| Delivery information | Fully assembled |
| Required accessories | Slide rail: Length calculation,For use as a drive:Assembly moduleDrive kitMotor support |
| Size [b] | 120 |
| Material information | Housing: Diecast aluminum, powder-coated,Chain wheel: PA,Chain guide: PA,Hexagonal shaft up to size 160: PA, from size 160: Non-rusting steel 1.4301 + PA,Connector: Steel, galvanized,Ball bearing: Non-rusting steel 1.4301/FDA |
| Track width in direction of transport [b] | 120 |
- Reduced noise emission due to slide rails guided in the return unit
- Installation of the drive kit possible on the right/left (motor, coupling, flange)
- Drive of a parallel conveyor section or bridge using a hexagonal hollow shaft integrated as standard
- Ball bearing made of non-rusting steel (1.4301), with seal on both sides and FDA-compliant grease filling
- Side elements with slot to attach holders for lateral guides, or similar
Ball bearing made of non rusting steel (1.4301), with seal on both sides and FDA compliant grease filling, Installation of the drive kit possible on the right/left (motor, coupling, flange), Drive of a parallel conveyor section or bridge using a hexagonal
Slide rail
Slide rail
Easy assembly - simply clip onto the section profile Secured against axial shifting due to lateral boltingCAD data
Assembly module AL
Assembly module AL
Assembly instructions
CAD data
Drive kit
Drive kit
The adjustable ball catch coupling is protected and integrated in the flange to save spaceCAD data
Transmission kit
Transmission kit
Installation of the drive kit possible on the right/left (motor, coupling, flange) Stainless steel ball bearings, with sealing on both sides and FDA-compliant grease fillingCAD data
Section support 65-120 AL
Section support 65-120 AL
The chain conveyor 65-120 is placed on the ground and fastened by means of supports or even suspended from the ceiling. The suspension needs to be determined depending on the application.CAD data
Section support 160-320 AL
Section support 160-320 AL
Holder is easily centered in the slot thanks to centering lugs Very simple assembly thanks to pluggable screw connection Easy-to-clean design with draining surfacesCAD data
Return unit AL
Note: High-pressure cleaning of the ball bearings is not permitted.
Thanks to the innovative drive concept, the return unit can be operated simply by itself or supplemented with a drive kit to be operated as a head drive without chain bag. The section length is limited to a maximum of 7 m.
Size: all track widths Suitable chain types: all Permissible chain tensile forceReturn unit function: Fmax = 1250 N
Head drive function without chain bag: Fmax = 600 N
With shortened maintenance interval, due to chain elongation
Section length for return unit function: L ≤ 30 mSection length for drive function: L ≤ 7 m
Conveying speed: vN = 2-60 m/min, other speeds available on request Use in combination with the drive kit as a wedge conveyor drive Not suitable for reversible operationInnovative drive concept
Combination matrix
|
Straight |
Curves |
Drives |
Return Unit |
||||||||||||
|
Section profile AL open |
Section profile AL closed |
Assembly module |
Curve wheel |
Roller curve* |
Horizontal sliding curve |
Vertical curve |
Head drive |
Curve wheel drive |
Connection drive |
Center drive (STS)** |
Basic unit |
90° (STS)** |
Transmission kit |
||
|
Straight |
Section profile AL open |
J |
|||||||||||||
|
Section profile AL closed |
J |
J |
|||||||||||||
|
Assembly module |
J |
J |
N |
||||||||||||
|
Curves |
Curve wheel |
J |
J |
L2) |
L2) |
||||||||||
|
Roller curve* |
J |
N |
J |
N |
L1) |
||||||||||
|
Horizontal sliding curve |
J |
J |
J |
J |
N |
L1) |
|||||||||
|
Vertical curve |
J |
J |
J |
J |
L1) |
L1) |
L1) |
||||||||
|
Drives |
Head drive |
J |
J |
L2) |
L2) |
L1, 4) |
L1) |
L1, 4) |
N |
||||||
|
Curve wheel drive |
J |
J |
L2) |
L2) |
N |
L1) |
L1) |
N |
N |
||||||
|
Connection drive |
J |
J |
L2) |
L2) |
N |
L1) |
L1) |
N |
N |
N |
|||||
|
Center drive (STS)** |
L5) |
L5) |
L2, 5) |
L2, 5) |
N |
L1, 5) |
L1, 5) |
N |
N |
N |
N |
||||
|
Return Unit |
Basic unit |
J |
J |
L2) |
L2) |
L1, 4) |
L1) |
L1, 4) |
L2) |
N |
N |
L2, 3) |
L2, 3) |
||
|
90° (STS)** |
L5) |
L5) |
L2, 5) |
L2, 5) |
N |
L1, 5) |
L1, 5) |
N |
N |
L2, 5) |
N |
N |
L2) |
||
|
Transmission kit |
N |
N |
N |
N |
N |
N |
N |
J |
N |
J |
N |
J |
N |
N |
|
|
J |
possible without restrictions |
* Support profile must project 76+2 mm into the roller curve. |
|||||||||||||
|
L |
possible with restrictions |
** AL-STS adapter included in the scope of delivery. |
|||||||||||||
|
N |
not possible |
||||||||||||||
| 1) | Profile connector not required |
| 2) | Use of a profile piece (Lmin = 120 mm) |
| 3) | Assembly module required |
| 4) | For sizes 160-320: shorten the support rail on the dotted line |
| 5) | Use of the AL-STS adapter |
Request Quote
How to Find Us
If you have any questions, just fill in the contact form, and we will answer you shortly. If you are living nearby, come visit us.